---
product_id: 49042246
title: "COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module"
brand: "collence"
price: "€ 60.78"
currency: EUR
in_stock: false
reviews_count: 2
category: "Industrial"
url: https://www.desertcart.fi/products/49042246-collence-3d-printer-heating-controller-30a-heatbed-mks-mosfet-extruder
store_origin: FI
region: Finland
---

# COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module

**Brand:** collence
**Price:** € 60.78
**Availability:** ❌ Out of Stock

## Quick Answers

- **What is this?** COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module by collence
- **How much does it cost?** € 60.78 with free shipping
- **Is it available?** Currently out of stock
- **Where can I buy it?** [www.desertcart.fi](https://www.desertcart.fi/products/49042246-collence-3d-printer-heating-controller-30a-heatbed-mks-mosfet-extruder)

## Best For

- collence enthusiasts

## Why This Product

- Trusted collence brand quality
- Free international shipping included
- Worldwide delivery with tracking
- 15-day hassle-free returns

## Description

Usage: 1. Plug a power supply. 2. Connect to heated bed. 3. Connect digital control signal to GND, D8 of MKS Mini. 4. Connect to the heated bed signal on Ramps1.4 or MKS series controller boards. Notics: 1. Only can choose 3 or 4 signal group. 2. Pay attention to polarity. Package includes: 1 x Heating Controllor MOS Tube

## Images

![COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module - Image 1](https://images-na.ssl-images-amazon.com/images/I/51ldDLgsueL.jpg)
![COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module - Image 2](https://images-na.ssl-images-amazon.com/images/I/41041HIIC6L.jpg)
![COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module - Image 3](https://images-na.ssl-images-amazon.com/images/I/51zTMe-6PVL.jpg)
![COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module - Image 4](https://images-na.ssl-images-amazon.com/images/I/41wHpHsUoUL.jpg)
![COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module - Image 5](https://images-na.ssl-images-amazon.com/images/I/51L0J1UXyoL.jpg)

## Customer Reviews

### ⭐⭐⭐⭐⭐ Perfect for 3D bed heaters
*by C***D on March 4, 2018*

I've been using this on my Tronxy X5S inline for the headbed, and it's been doing a great job.  The fins get to about +10°F from the ambient temperature of the room, not enough to notice most times.  It cut my bed heatup time to under half the previous time, and should be fine to upgrade to 24V when I update the bed power supply down the road.

### ⭐⭐ Died in less than 5 months.
*by D***Y on October 31, 2017*

This is the same as the TriGorilla one I put in an earlier printer.  This one went into a Monoprice Maker Select Plus printer.1st this board is large.  I had to trim about a 1/4 inch off the circuit board to get it to fit in the Plus chassis.  But with the extra wiring added to get the cables to reach, it was quite easy to wire up.  It also takes a lot more current than my heat bed can produce to overwhelm it.  It should be a good protection instead of the old connections running all current through the motherboard.  Ive run this printer and MOSFET up to 100 degrees C and it showed no sign of problems providing the current necessary.  Works on either 12V or 24V which means its perfect for most 3D printers.  Much better than the BIQU one I looked at.  It was however one of the more expensive MOSFETs I looked at but is worth the price.Update 03-18-18:I have smelled something a little smokey for the last few days around my 3D printers but couldn't determine the source.  03-17-18 The heated bed on my Monoprice Maker Select Plus was no longer warming up.  I troubleshot the printer and found the board and heat bed and wiring OK.  But this MOSFET has gone bad and was the source of the smell.  It had voltage coming into the board from the power supply and motherboard but would not switch on.  I removed it and redirected the heatbed wiring back to the original motherboard connector.  All is now working again.  I will have to get another MOSFET.  I reduced the rating to 2 stars because it lasted less than 5 months.

---

## Why Shop on Desertcart?

- 🛒 **Trusted by 1.3+ Million Shoppers** — Serving international shoppers since 2016
- 🌍 **Shop Globally** — Access 737+ million products across 21 categories
- 💰 **No Hidden Fees** — All customs, duties, and taxes included in the price
- 🔄 **15-Day Free Returns** — Hassle-free returns (30 days for PRO members)
- 🔒 **Secure Payments** — Trusted payment options with buyer protection
- ⭐ **TrustPilot Rated 4.5/5** — Based on 8,000+ happy customer reviews

**Shop now:** [https://www.desertcart.fi/products/49042246-collence-3d-printer-heating-controller-30a-heatbed-mks-mosfet-extruder](https://www.desertcart.fi/products/49042246-collence-3d-printer-heating-controller-30a-heatbed-mks-mosfet-extruder)

---

*Product available on Desertcart Finland*
*Store origin: FI*
*Last updated: 2026-02-20*