Lund SX110S Elite Series Black Sport Style Standard Fender Flare - 4 Piece

Ok so here's the deal with the clips - at first I thought "there's no way this will ever work" BUT when you actually get them on, they hold TIGHT. But the holes in my flares were too far from the edge for the clips to reach, so I called Lund and they recommended I dremel away material from the edges so the clips can reach the holes. Took me about 5 minutes per side, and now they're on tight. Really a pretty ingenious solution.Be sure that when you dremel (if you need to) that you remove the full width of the clip plus a little extra or it will be a pain. Also if the rubber seal got messed up during install, you can probably roll it outward with your fingers enough to fix it without undoing everything.Also, do what the instructions say and start from the middle for both front and back, otherwise you're gonna have a lot of trouble.

Not a specific fit, holes don’t line up. Gaps across the top. Had to buy self tapping screws to get it secure. 😒

Like most people with an HD GMC truck, mine gets used and after 12 years it is also starting to show some rust around the fenders. I tried a set of cheaper ones and they didn't fit at all. These fit really nice, especially at each end which is the most important to make them line up with the body. There are just some minor gaps in the tight corners but it isn't an issue and it isn't visible once installed. Material will likely get scratched and scuffed, but that's life for these trucks. I couldn't make the factory screws work as they are too short. Go get a box of #8 x 1" self drilling screws and just screw them on. I used a few extra as well. I didn't even try those little clips they sent for the rears. Total job was less than 90 minutes once I had the screws I needed. Not sure why this would take someone more than a couple hours. Note that I could not make my mud-flaps work with these, and they do make the factory size tires look a bit skinny! I may look for different offset rims to make it look a bit better.

Fit truck nice. Putting on the gasket is a little time consuming, but not difficult. Job takes a few hours to get it done.

They do not fit perfectly so there for the seal is not sealed 100%

The fender flares themselves look good after their on, but putting the rubber seal on each one individually was a pain! Then you have to take the tires off the truck cause the holes don’t match up in the front so you need 2 People to install drill different holes and screw in! The back ones are fine cause of the clips that come with them, but I think it’s kinda of a cheap deal all others I have put on have had screws all the way around but the clips work! After there on the truck it looked really good! Mind you it was a whole day project!!

Fit decent on the front, yet the rear were a difficult fit and install. Supplied clips wouldn't hold had to be replaced by screws. Expected more from a name brand product.

Installation was fairly simple for the front two fender flares. The rear were a total pain and took way too long to install. The holes that are cut in the plastic are not in the correct location, so I had to use my dremel to make the holes a little closer to the rim of the flare so that the clips would actually fit. The top of the flares seem impossible to keep flush and tight to the truck. Every time I go through a car wash, the rubber seal comes off part of the top of the flares. No more automatic car washes for me! The rubber is constantly coming off on the top, especially after driving at speeds over 55mph. I wish there was a way to keep it all tight.

Works great on my 2008 Sierra. Box fenders are rusting these cover it up perfectly.Clips are useless so some drilling and screws are required. May need a second set of hands to hold in place while installing.

The fender flares were advertised as having been returned, but complete and unused. They were unused but were missing the the nylon rivets that attach the flares to the truck. 32 rivets and nuts to be exact. Made the "deal" far less worthwhile.

Pre drilled holes do not line up, and of course you will need a lot of time to fit them and a lot of tape so they stay where you want to install them

Horrible fit, don’t buy. You have to pay or the return postage yourself for a product that doesn’t fit well

Wrong fitment for application! I have a 2010 gmc sierra 1500 and they do not fit !