Zone Tech Bumper License Plate Relocator - Premium Quality Classic Black Universal Fit Front Bumper License Plate Relocator Bracket Holder Bar

Sturdy metal, just as the picture shows, that is all that you receive in this package. I ordered the plate for a next day delivery and found it quite affordable and very quick to receive. There are no instructions, but the concept of the frame and what your trying to do doesn't necessarily yield one to need instructions. But of course, I did have a deer in the head lights look for just a moment, I cannot confirm if I did it correctly, since I didn't have instructions as to what to do with the smaller two holed metal pc that is about 2.5 inches, is I placed the screws with the thread up through two holes I created using the 2.5 inch plate as a guide from the bottom of one of the wider grill marks of my Honda Fit. And then placed the longer L shaped frame above it, to then screw in the two bolts on top. It was easier for me to fit my arm through the hood/bumper area by taking off a clasped cover under the hood, than it was trying to get under the car. Please keep in mind, if you are using a ratchet to tighten the bolt, it is Metric and not Standard, as my Dad had to school me in. Over all, good purchase, and for a girl, it probably took me 20 minutes to install.

Seems to be a legit plate bracket. Little bit harder to find placement for my vehicle but was able to be accomplished. It's made of very thick metal and has zero flex to it and feels very well made and put together.Hardware was a little on the short side but was able to scrounge up longer hardware to mount and it does a good job of holding to the valance of my car... time will tell if it stays put and I don't think I'll be going through any car washes with this attached now... just my vehicle though. Will write a follow up in a few months to update.

A great license plate relocator for the 05 350z. I did not what to use my tow hook and that would block almost 1/2 of my useable airflow into the radiator (do not let the 350z grill fool you, the actual opening is not big). This relocator allowed me to adjust the license plate off to the side securely using the grill as a mounting point.

I used this Zone Tech Bumper License Plate Relocator with several large fender washers and a nut and bolt to attach it to the hold-down loop inside the bumper air scoop on my 1999 Mazda Miata without drilling. Very easy and secure. I offset the front license plate to leave the air scoop open. It is very sturdy and works well even when I hit the bottom on an apron dip or in the parking lot curb stop. Glad I found it.

A must have if you state requires you to have a front license plate. And if you don’t like to drill on your bumper, this is the perfect solution. Already been using over a month, driving on the highway, Carwash and even a ditch! Still solid!!

Allows you to mount a plate just about anywhere. Worked perfect for my 19’ 2500 ram! 👍

I refused to drill holes in my front bumper so this was the most cost effective way to get around it. I a few months a front license plate won't be required so why spend 80 bucks on a sto n show when this works perfectly well. One of the best purchases I've made on Amazon.

Super simple install, drill two holes using holder as guide, place holder and smaller metal brace on each side of I stall site, install bolts from bottom up and tighten up. Took maybe 10 min total.

Actualización:Al inicio parecía una excelente opción, pero al pasar por una rampa, se me cayo la placa... no indica que el producto sea malo, pero no aconsejo atornillar por debajo de la facia....Actualmente en mi estado empezaron a multar si no presentas tu placa delantera. Y este portaplaca fue la mejor solución que encontré.El resultado habla por si solo, quedo muy bien fijada.Ojo: Si miran el manual en la ultima imagen del producto, se sugiere que los tornillos principales deben sujetarse de la parte de arriba de la placa, pero en mi caso me funciono mejor sujetarlo de manera inversa.... de esta manera taladré mi facia pero de la parte inferior y asi no se ven los orificios...No olviden que la plaquita pequeña suelta se coloca entre los tornillos y el pedazo grande de metal... es para tener una mejor sujeción.

I was very skeptical about buying this product and having to take off my bumper, I was able to drill it just above my lower grill and then attach upwards and bolt it... Its very sturdy and very high quality for the price.. If your skeptical like me just send it and buy it, You won't regret it!!

Great buy, solid metal not sure if it’s steel or aluminum. But it’s a solid 1/4” thick. Looks good on my car. For the price it’s fair but if it came with black plugs for the bumper where the old one was I’d pay $5 more but for the $20 it was more then fair. But I used self taping screws I had that are tamper proof torx.

I was looking for any plate relocation kit forever as I have no toe hook screw in, then I found this product. I thought it would be plastic but it's high quality metal. The instal for me was kind of tricky because my srt has a funny front bumper however I got it done relatively easy and it looks exactly the way I want it to. I love it, side note I was willing to pay up to 100 for it so getting it for under $20 in my mind I was like. "Start the car start the car" if you get that you get it. Anywho 5*️⃣*️⃣*️⃣*️⃣*️⃣

Installation was rather difficult on my 2006 Civic Si, as I had to drill into the plastic in a forward angle. Otherwise I would have had to remove the bumper. But It looks decent and only wobbles a little.