Husqvarna 952711918 Leaf Blower Gutter Kit Genuine Original Equipment Manufacturer (OEM) Part(125B Or 125VBX Only)

I appreciate all the reviews on this product hence my purchase of one! Super easy to put together and attach to my Husqvarna 125b leaf blower. My house is a one story ranch so this attachment was a life saver!! No more ladders and very easy to clean gutters. This product fits the Husqvarna 125b as expected and works very well.

This product, once modified to work with a HUSQVARNA 150BT, does work.You'll have to remove the flange at the elbow piece that attaches the piping to the blower. I used a small hacksaw to cut it off. A Dremel would have been more precise but slower. When you do, you will leave a hole in the elbow piece. Take a piece of duct tape and cover the hole. You can now install the elbow piece by removing the "tube" (the black plastic pipe that you wand around while using the leaf blower) and inserting the newly modified elbow piece.Pros:- It works well. I tested it on a number of my gutters. Compared to using a ShopVac with virtually the same type of plumbing system as this product, I can clean the gutters in about 1/5 of the time when using the Husqvarna instead.- It's easy to assemble. The modification to the elbow piece took less than five minutes. And I am not a "handy" person. I just took a hack saw and cut off the flange and duct taped the hole. Assembly onto the blower itself took another five minutes, only because you have to loosen that bolt in the clamp/hand throttle and that bolt on my blower is a pain to deal with.Cons:- You will quickly learn not to run the blower at full throttle when using this product. It's basically 10 ft tall, plastic air blowing cobra. Set your throttled at about 25% power. That should be sufficient.- The plastic they used in making the product is flimsy. This is supposedly an OEM product from Husqvarna. I find that hard to believe. The plastic is soft and was misshapen when I pulled it out of the box. But because it was so flimsy, you can easily mold it back with your hands into the right shape. It all connected up nicely.- Because the plastic is flimsy, and you're blowing a lot of air through it, it's a bit awkward to use. It may take you a couple of minutes to get the hang of it, but once you do, I think you will like it. Beats getting up on a ladder or using the ShopVac equivalent.- And because the forces this product places on the rest of the plumbing of the blower, check and tighten all of your connections all the way up to the blower. The elbow piece that connects the plastic plumbing to the blower itself popped off while I was using it. To be fair, it was the first time I had checked that connection since getting the blower years ago.Overall:- Not what you'd expect from Husqvarna. I would have expected higher quality.- Requires a simple modification to run on a 150BT, but if I can do it, any of you can.- It's a handful when running it at speed.- It does work well. It will blow your gutters out nicely.- It's reasonably priced. This keeps me off the ladder and roof. If I break this product using it, it's still cheaper than breaking my body if I fall off the ladder or roof.

This product exceeded my expectations! The piping was easy to put together, once assembled the piping is very ridged and seems very strong. When fully assembled and attached to the leaf blower it is very manageable and not top heavy as I would have expected. It fit my Husqvarna blower perfectly and had very good airflow to the tip. I first used it in December when the leaves in the gutters were wet, be prepared to get very messy when using it. It blew debris all over me, but it got the gutters very clean. I am extremely happy with the purchase, it truly does work as advertised!

This item works fine. I don't have much to add to the many positive reviews, because it is a simple contraption that does the job. I don't actually use it for my gutters, because I have screen leaf guards on them, but I need this to clean out behind the corner "gusher guards" that collect debris. Yes, you get quite dirty when using it; big deal. As for the folks who said it doesn't fit their blower, the item description says plainly that it is for "125B, 125BX & 125BVX handheld blowers only." If you have a different blower, why would you complain that it doesn't fit? BTW, the initial assembly of the swivel tube to the elbow tube is a little tough, but you only have to do it once. After that, assembling the tube sections and attaching the elbow section to your blower takes just moments. This was a good purchase for me and it will be for you, too, if you have the specified blower.

I am someone who is easy to please. I generally like most things I purchase. But this blower gutter kit is one of the worst purchases I have ever made. Where to begin...- The instructions are horrible. You would think it would be easy to figure out but it really is not as straightforward as you'd think.- The parts are garbage. On one of the cylinders, in order to make it fit onto your existing blower, they literally just ran the part through a band saw to make a slit in the part so that it will be able to clear some existing component. The plastic is all serrated from where the saw ran through it. Super low quality.- It doesn't work! After all the parts are together, you're left with gaps in the fittings that let so much air out, there isn't enough forced air to clean your gutters.Despite all of this, my wife and I tried running this together and the absurd balancing act of trying to aim the top of this product into the gutter and keep the rest of it from falling apart was truly hilarious. Not to mention, the air blowback from the gaps means you're basically leaf blowing yourself! We were dying laughing at ourselves and how we probably looked to the neighbors. Maybe I should give it 2 stars for all the laughter we had and the memory we made.

No clear directions/assembly in English,,I received 2 manuals both contain 60 pages each & only 2 pages total are in English & is very generic instructions & illustrated parts diagram 1 uses letters to ID parts & assembly diagram uses letters,total confusion in attempting to follow manual for assembly,,add-on,the pivot piece arrived cracked at the bottom,,after figuring it out on my own,it works good,,it is a bit awkward when using all the extensions,,good for a max of about 12 feet & manage to hold it with 2 hands