TRQ Front Driver and Passenger Side CV Axle Assembly 2 Piece Set Compatible with 2012-2017 Toyota Camry 2.5L I4 - Verify Fitment, Engine & Trim

I was very satisfied with this dual front CV axle. The quality felt solid and well made, and it fit perfectly with no issues during installation. After installation, the vehicle drove smoothly with no vibrations or noise, even during turns. It completely restored proper handling and eliminated the clicking and shaking I was experiencing. Unfortunately, snowy weather later destroyed my car, but up until that point, the CV axle worked great and performed exactly as expected—especially compared to the price my dealership wanted. Overall, it was a reliable replacement and an excellent value for the cost.

They fit perfectly, I will be updating the front end of my truck, trq will now be my go to

I used to repair the axle, replacing the rubber, but it did not last long and when you compare prices you wiill notice it is cheaper, faster and safer to replace the hole part

They ran well for one year until a friend of mine got stuck in the mud. While I was pulling him out, I heard a clunk in the front. After pulling the axles, I found out that one broke and spun. I will not buy this brand again. Beware they are not made in the USA and are cheap China junk. I learned the lesson again that you got what you paid for.

My dad's a machinist and I grew up in his shop. I've worked in fabrication, assembly, and quality control. I've personally replaced a handful of CV joint sets on various vehicles over the years, and always with automotive store bought parts. Auto parts store products carried a premium, but the quality was reliable. This was my first attempt purchasing from this company (without the middle man) and I thought it risky. My fears turned out to be unfounded. The axle assemblies are machined well and I can tell quality manufacturing and talented assembly went into the finished product. The type of steel and heat treating is correct, the splines are tight tolerance with no wiggle. The spider gear doesn't drag and it's nice and tight; same with the races & housing on the other end. The boots are surprisingly thick and a good grade of rubber. The clamping straps were even applied with care. I'm impressed, and I'm not impressed often. The ONLY criticism I could come up with is that the tool marks weren't polished off all of the steel, but that's cosmetic and would only matter on a show car, maybe not even then. It's obvious from the way these axles feel that care was taken to ensure a high quality product was shipped out. The boot clamp tabs were even neatly folded over. The entire axle was lightly oiled and placed in a thick mil plastic bag, then supported with foam braces, and placed in double thick cardboard boxes. There were instructions included, which would help a novice. The only thing better about my OEM axles is that they have rubber vibration dampers on the shaft, which the replacements don't have; I doubt I'd be able to notice the difference though. The car drives like butter compared to original axles. For the price, I think I got a bargain with this quality. I'm not sure what to do with my cores... Parts shops used to want them in exchange...

The cv axles themselves were top notch. Good quality, once installed they fit perfect. The only issue I had was the circle clips that were on the spline side of the axle. For whatever reason they made it impossible to seat the splines properly. I ended up having to remove the cirlce clip from the old axles and place them on the new ones. After that they snapped right into place as they should have.

Update: there was nothing wrong with the TRQ CV axle that had been installed. Had a Toyota CV axle installed and still have the same sounds. Get your problem professionally diagnosed before spending your time and money. Here are facts for your consideration. I had my passenger side replaced first because the boot was torn. That CV Axle assembly seems to be doing fine so far. Then I spent $380 to have the driver side CV axle replaced because there was clicking when I turned right. Now the clicking is not as bad but still there. So I wasted 380 dollars having a defective part installed. Local mechanic said he's never seen so many after market part failures as he sees now. I'm going to buy a Toyota CV axle now. I suggest you do this from the start.

If you know how to put it on you shouldn't have a problem with this product. Haven't had any issues with it after several months installed.

Semble de bonne qualité et instruction facile reste à voir la durée de vie 🤞👍

Good quality and fit perfectly on forester SJ 2015

كشكل ومضمون يبدو ان خامته وجودته ممتازه لكن للاسف لا يوافق سيارة ميركوري ميلان مديل2010 محرك6سرندل واتمنى التوضيح او تغير او حذفه من موقعه بانه موافق سيارة ميركوري ميلان مديل 2010 سعة المحرك6سرندل (انتظرت كثيرآ وبالتالي لا يوافق مركبتي وهذا في غاية السوء) وزاد السؤ سوء الى الان لم يتم اسنرداد مبلغي المالي