Auto Ventshade [AVS] Bugflector II Hood Shield / Protector For 2008 - 2013 Ford Econoline Vans, 2008 - 2026 Ford E - 450 Super Duty | High Profile Bug Deflector, 1 pc. - Dark Smoke | 25016

Super easy install. looks and fits perfect on my 2009 Ford E-350 van. If your hood doesn’t close after the install, remember to adjust up or down on the 2 huge rubber hood stop screws on each side of the front of the engine compartment that determine the height of the hood when latched a couple turns up or down will do the trick. Great seller too.

2015 Minnie Winnie 25b. Easy 30 minute install. Required drilling 2 pilot holes. Happy with the outcome.

Fits "nearly" perfect.In general this fits 100% but I did elongate the holes side to side to give me a little adjustment room.My driver side was a little tight to the headlight edge so I could move it toward the passenger side a little to gain room, and it was perfect.Well made great item for our 2018 dynamax isata4 31ds, ford E450 chassis.

Fitment: There is some confusion in the reviews about which vehicles this part was made for. I installed this on a 2019 Ford E450 C-Class Motorhome chassis, but also fits a few other years/models. See my photo for the parts application sticker that came on the deflector for details.Install Tips: The included instructions are decent. It took me about 20 minutes. Take your time and review the drawings for an easier install. Start by removing just the four specified under-hood rubber strip clips. These clips will not be reused.The four larger under-hood mounting screws are self-tapping, so you just need a large size Phillips screwdriver to tighten those.Always wait to install the two outboard screws after installing the main four screws. Even though they call the two outboard screws "self-tapping", they are not. Thanks to other reviewers I had a drill and 1/8” drill bit ready to go.NOTE: Be super careful to only drill (about 3/8" max) into the underneath part of the hood; and not up through the top surface of the hood!Finally, remove the tape film to expose the two-sided tape adhesive only AFTER drilling the holes, and then install the four provided rubber bumpers to keep the thinner end sections from fluttering and hitting the hood at speed.Fit and Finish: After installation I closed the hood and noticed that the deflector is off-center about 3/8” (toward the driver’s side) where it almost touches the chrome grill. Clearance on the pass. side is ok. I may decide to carve/sand that edge back for more clearance later on. I can imagine it is difficult for the manufacturer to perfectly mass-produce an acrylic molded shape every time.Final Thoughts: The deflector definitely looks like an "add-on" but for me it is more about the function than the appearance. I expect (hope) it works to keep bugs, and more importantly rocks, off the windshield.

Works great. The self tapping screws are worthless. Had to predrill holes then use the screws provided. No big deal . I would buy again.

I accidentally ordered two of these - and they both came so promptly that I found a use for the second as soon as I had the first one on my Ford E200 van. This deflector fit well with no problems. It also has lasted through the last year and several trips around the country at speeds I won't write down because that would constitute evidence. I put this deflector on when I was also installing a solar panel on my roof; so I found a use for the second deflector by putting in on my desktop sander and sculpting it to fit the top of my van. Now it deflects the flow of air up and over the solar panel, resulting in less drag and no decrease in miles-per-gallon. Good product with no problems.

Vent shade looks great on the work van

Judging by the comments, it was hard to tell if this would fit my 2022 E-350 knapheide KUV cutaway van. It fit perfect. I hate the old man look. But I couldn't stand the extreme amount of stones and bugs that I have gotten with this brand new vans windshield. It works, maybe not perfect. But it seems to have brung the ratio back to a normal vehicles windshield amount. I hate the look, but... it needs it, and this works. Thank you

Good !! Perfect to not broking the hood 👌🏻

everything was 100 % great , very good support

It was exactly what I wanted

Excellent

looks great and easy install about 10 min