3/4" 18445 Vinyl Labels (2-Pack)

I was a little hesitant to order these, because there are a few reviews complaining about quality of the labels, but there are also a number praising them, and at this price it's worth the risk. Long story short, the labels are just fine. I'm attaching a picture of this label vs OEM label (OEM label is on the right). I'd say they're almost identical, with a slight different in finish (OEM is slightly less shiny), but you can't even see that from the photos. Will definitely stick to these from now on.

I purchased 3 rolls of this labeling material. I hope the ink does not dry out before I use it all. As for the initial roll it looks good with good solid ink. It is difficult to peel the backing off of these labels, but they do stick well once you get there.

I use these labels with no issues… for audio cables , power cables , DMX cables etc. , audio equipment and accessories such as DI boxes , mic stands etc. the concept in my case is to quickly identify the cable or accessory for when times to install or tear down. Can help to avoid confusion with others people cables / accessories. Might be helpful for those colleagues , musicians etc.. that might forget what not belongs to them or forget that they did not bring theirs and prefer ( look for opportunities) to pick that one not labeled that is very similar of what they still have at home 😳☺️. Also .. labeled cables , cases etc. it say much about you “ organization skills “ and SAVE money through inventory control and accountability. Thank you

Other than the OE labeling on the cassettes it seems to be identical to the OE media, I have not used the all of adhesive tags but Nylon and the shrink tube ( white ) prints cleanly, I can't speak for shrinkage. over all they seem to be good value, worth a try, I can't say at this point if I would recommend them but My initial impressions are positive. They are not expensive to at least try, The Dymo machine that they are for is very good the OE media is ( shrink tube ) is quite expensive.

These cartridges jam and mis feed. The label gets jammed inside the 5200 printer and the black layer film comes out. I managed to get some labels created and the print quality is good. I labelled my ham radio equipment and all of the labels are peeling up. These label cartridges are not very good.

Make sure that the little wheel that has the letters and numbers doesn’t have any old label tape on it. I put in a new cartridge and it wouldn’t make good labels. This used to be my wife’s label maker from work and she’s the one found that there was old label tape on the letter wheel

I tried these as I make a lot of labels and the DYMO brand is pretty costly ... I was pleasantly surprised that these cartridges looked the same and performed as well, and maybe even a little better in my DYMO label maker as their more expensive ones did ... clear printing, no jams ... great cartridges ... I will definitely order them again!

Using the 3/4" version of these labels in my Dymo Rhino 4200. The print quality is good and the adhesive on the tape seems strong. The problem is the backing paper. Good luck getting it off. The backing paper is is not split down the middle, which would be optimal. The backing paper does have a split/seam, but it's an odd one. The split is about 1/16" from one edge and the backing paper is impossible to remove with just your finger nail. The only way I was able to get the backing paper off was to use a box cutter with a sharp blade to pick at the narrow 1/16" strip until I could peel it off, then do the same for the rest of the backing paper. This is a real time sink when making multiple labels. I used this tape to relabel my main electrical panel and sub panels. 42 labels in total and I had to spend about 30 seconds for each label, peeling off the backing paper. Doesn't sound like a lot of time, but it sure got tiring after about the 10th label. One of the main draws for a label printer is the ability to just print a label and immediately slap it on something, no muss or fuss. These labels are a pain to use, but I guess if they stick well and don't fade over time the effort will have been worth it.

Do the Job

The labels are used to identify client panels so adhesion is essential, so far so good!

👍🏻

La parte central de la pegatina no se imprime Cuesta mucho quitar el papel del adhesivo

I cannot find a difference between original and this ones. I have read reviews says that does not stick well but it’s not true. I have read reviews about print quality but it prints same as original ones. For sure I will order again!!!!