Motorcycle Stand Rear Combo Wheel Lift Stands, 500Lbs Capacity,Swingarm Spool Paddock Stands for Sport Bike,Fit for Yamaha Honda Kawasaki

I got this stand for use with my 2023 Honda Rebel 500. It is a single stand (not two “stands”) that comes with L-shaped rubber-lined lift brackets for under the swingarm and C-style lift brackets for swingarm spools or front forks. It was easy to assemble, seems plenty solid, and works very well, now that I have corrected a minor issue (my fault) that other reviewers have mentioned and should be aware of.When I first lifted the rear wheel, the lifting arms skewed to the left and the bike was not quite vertical. The rear tire was still in contact with the floor, and the bike seemed unstable. This happened, not because of a design flaw in the stand itself, but because I had lifted the bike while it was on the side stand (leaning to the left). The solution is to have the bike as vertical as possible before lifting it. I did this by placing a piece of 2x4 under the side stand, but having a friend help would probably be safer, especially if you have a heavier bike. Once I did that I was able to lift the bike very easily.I have not used it to lift the front wheel, so I can’t comment on that.Another thing to be aware of: depending on your exhaust setup, you may need to remove your muffler(s) in order to lift the rear of the bike because there could be an interference issue with the stand. On my Rebel this only requires the removal of one bolt and a clamp, but it’s still a bit of a pain if you’re just doing chain maintenance. There are upswept (or shorter) aftermarket mufflers that wouldn’t interfere with the stand.As other reviewers have mentioned, the distance between the lifting arms is actually 14.5”, not 12.6" as shown in the pictures, so check your particular bike to make sure it will fit. The 12.6” dimension is actually the height from the floor to the center of the lift bracket post, which only gets my rear tire (150/80-16) about 1/2” or so off the floor.Overall I find it to be a very good stand for the money, and I would recommend it as long as it fits your bike and you use it properly.

Does Exactly What You Need — No Hassle, No WobbleThis stand impressed me. Came 95% assembled—just had to tighten two bolts and I was lifting the rear wheel in minutes. Used it to change out the chain, sprockets, and clean everything up. Lightweight but solid, no flex, no sketchiness. Locks in steady and rolls easy. Honestly feels like a no-brainer at this price.

Works great for a 2018 Honda Rebel 500. Product is heavy duty and arrived partially assembled. Be cautious when ordering the description is a little misleading making you think all the colors are a front and rear. So pay attention if you want both. Highly recommend spending a little more for both! Made working on my Honda very easy!

Easy to assemble, very stable stand, lifts motorcycle easily.Half the price of other stands and does same job. Has both brackets for lifting the front or the back. Very easy to adjust width of brackets to accommodate swing arm size with spools. Length of handle makes lifting very easyMinus the one star: scuffs and blemishes on surface, looking inside tubing can see rust spotting. Makes concern of longevity of metal tubing.

This is a lot heavier duty than it looks in the pictures. Works great to jack up the rear on my Kawasaki Versus-X 300. The front though is going to be a little trickier. I'll weld on some 1/2 rebar with a nub on the end so it will fit in the bottom holes in the forks. It won't work to jack it up to remove the tire if you use the axle bolt/nut to lift it up. I also used a block and tackle with a cable hanging from the garage rafter to straighten the bike upright since I'm working alone.

This does not fit the front. The description says "front and rear combo" but shows only one stand in the picture. I already have a rear stand and needed a front stand. I (as well as others who have left reviews) thought the description meant this could be adjusted to fit either the front OR the back; however, according to "What's in the box", there should be two stands, one for the front AND one for the rear.You can argue the misunderstanding is my fault, but I expect a seller to provide a clear and accurate description to include pictures of the exact item I will receiving unless otherwise noted in an obvious way.I also ordered the item that shows both stands in the picture for my other bike. Those stands do both fit as described.In short, this post shows only one stand (which fits only the rear) and is described in a way that sounds like the one stand can be adjusted to fit either the front or the rear, yet the full description is for both stands to be included which is why I am giving this a one star review. Now I have to go through the return process and order another stand that does specify "front only" and has a description that matches the pictures.

Good quality easy to put together light and durable works for it's intended purpose well bike feels stable on the stand good price too

First time using one of this stands and after watching a short YouTube video, this was a breeze, it literally took me 5 seconds to get my 460 pounds Honda CB650R off the ground for a wash and chain care. I really don’t see why I would pay a lot more for a different brand. Amazing product and price! Strongly recommend! (Never write reviews but I see some people complaining about the product and I don’t really know why, just learn how to safely use it first)