Creality Ender 3 Upgrade Print Bed, Magnetic Platform, 235 x 235 x 1 mm, for the Ender 3 / Ender 3 Pro / Ender 3 V2 / Ender 5 / CR20 / CR20 Pro

Good product once set up properly. Would say the magnetic part does seem weak but that's easily overcome by using some clips to help hold it down

Honestly should of bought this way sooner than I did even though the glass bed I originally had was okay ish the adhesion started to fade and even with hairspray or glue sticks it just was not happening (Yes my bed was level)This is super easy to apply just one note is take your time and you'll get it perfect.Definitely worth getting for prints and makes them soo much easier to remove would highly recommend.

I had some adhesion problems with my glass bed so I wanted to try this one and I found out that I have a dip on the middle of the bed.Overall magnetic bed itself is pretty cool.It’s a lot easier to remove a small print as you can bend the bed and it will pop off instead of trying to grip it with fingers and pulling sometimes risking breaking off small parts

I purchased this item because the magnetic mat that originally came with my Ender 3 Pro had been damaged. This was to be a direct replacement.When I first opened the package, first impression was that it looked identical to the original, but I then realised that it requires a magnetic sticker to be applied to the bed before it can be used.My first thought was to use the mat without this sticker as the bed on this model is already magnetic, but the mat didn't seem to have the same magnetism as the original and would slip around.What I then realised is that the magnetic poles on this new mat are flipped 90 degrees, so if you rotate it sideways (see photo) it grips perfectly.However, in this position, the tab that helps you remove the mat won't slide past the struts of the machine, so what I ended up doing was removing this tab. It's easy enough to remove without the tab anyway.If you're happy to use the provided sticker none of this is should be an issue for you, but I didn't particularly want to use it and favoured the above method to get closer to the original setup.Mat otherwise seems fine though, and my first print with it seems to be going perfectly. So overall, I'm happy with it.

This is second most useful upgrade to my ender 3 right after direct drive extruder. No problem with prints sticking to the magnetic bed cover, and no more need for any flat thin tools to try remove the print from the bed. This is so much easier with the elastic magnetic cover just lift it and bend it print comes right off. Also application of the magnetic sticker to the bed was easy enough - make sure to follow included instructions as they need to be correctly oriented for proper function of the magnetised parts.

Well that was a waste of money on my first print using this new magnetic bed. Some areas of the PETG did not come off and the bed stuck to the PETG print so badly that it just ripped the magnetic sheet apart.

It's best I ever used but it's wearing out and you need to remember nothing is forever

It did worked well at first but after a few prints it lost the magnetism so had to hold it in place with clips to stop it moving

El hecho que sea magnética hace que valga totalmente la pena

But now let me tell you the facts. READ THE INSTRUCTIONS The bottom layer only works magnetically in one direction. So if you do the bonehead move I did I just opened the package and slapped the sticky side down and thought I had a magnetic bed -Wrong, I was! I did not read the instructions. The bed piece actually must be aligned to properly function. And to get that sticky stuff off was not easy, didn't want to ruin it. But it has great adhesion at all temps. it is extremely easy to get prints off.

Har inte provat att printa ännu men ser ok ut

Très facile d'installation, attention, il y a tout de même un sens pour que le plateau s'aimante bien. Les impressions se fixent bien dessus, je n'utilise plus de laque. Et pour les retirer, rien de plus simple, le simple fait de soulever la partie flexible, et la pièce est décollée. Il est légèrement plus grand que le plateau chauffant d'une ender 3, il dépasse de quelques millimètres de chaque coté mais rien de gênant.

Favoloso, è un tappetino magnetico per la stampante 3D Creality Ender 3 Pro. Il tappetino è originale e mi sono trovato bene, fino da subito. Si tratta dello stesso tappetino uscito in dotazione alla stampante e ha le dimensioni di 235 x 235 mm per 1 mm di spessore. Altri tappetini dicono di essere magnetici, ma non lo sono, bisogna fare attenzione poichè li devi incollare sul piatto, creandoti problemi quando devi staccare il pezzo dal tappetino. Con questo tappetino non ho avuto nessun tipo di problema, poichè essendo magnetico si stacca e poi si può provvedere al distacco del pezzo di stampa.