SOCAL-LED LIGHTING 2pcs LED Load Resistors 10 ohm LED Bulbs Turn Signal Error/Blinker/Hyper Flashing (25W)

Used these on my 2018 Buick Regal Tourx for reverse bulb. Wanted LED lights in there, but installing them caused the reverse light to stay on all the time-- evidently the BCM expects an incandescent-like load on them, so a load resistor seemed like an easy way out.I chose 10 ohm, 25W for two reasons: The stock bulb is a 920 size incandescent which draws about 15 watts. At 14 volts (assuming vehicle is running), the resistor placed in parallel with the LED will draw about 19 watts. So 10 ohms might be a little overkill, but they're readily available, whereas higher resistance load resistors are not. 19 watts is awfully close to the 25W rating of the resistor, which means they will get HOT if used continuously. Not really a concern here, as reverse lights are used for short duration, perhaps a couple minutes max.It worked fine, LED lights work, they come on and off when they're supposed to. Good value, nothing about them made me skeptical of quality. The splice connectors are cheap junk, I chose to solder and use heat shrink wrap at every connection.

I was worried that these wouldn’t solve my LED light problem I had after I bought after market taillights for my 2015 Tacoma.. Well these absolutely solved the Hyper flash problem. They are very easy to install .. took me less than 20mins to install on both sides . They work and that’s all I care about.. now I’m not sure how long they will last .. but so far I’m so relieved and happy.

I had no issues installing this adapter, but the housing for the input side could be better.

Worked like a charm for hyperflash! I have no clue why the 50w resistors are even sold, as pretty much all incandescent blinker bulbs draw 20-30 watts. Lets help spread this information to the car community so that they don’t blow fuses or fry circuitry by drawing 50+ watts out of circuit that’s designed to handle 20-30 watts!Also, make sure to securely affix to a metal surface for heat dissipation purposes because they BY DESIGN convert electrical energy to thermal energy (heat) to apply enough of a load to trick the vehicle into thinking that you have OEM incandescent bulbs installed.

I got these cause I got LED brake lights for my 1998 Honda Accord.Since they only used 3 watts, my car thought that the lights had failed, and so I had a "Brake Lamp" light on my dashboard.Eventually I got annoyed of not having a clean dashboard, so I ordered these to fix it. (Original brake lights take 21 watts, if anyone needs to know)It was a little hard to install them, as the mounting screws I got would not fit past the cooling fins of the resistor. So I used my dremmel with a cutting disc as a grinding/sanding disc. Filing down the cooling fin near the screw mount so that I could securely mount it to the car's frame.I also put some heat reflecting tape on the trunk liner, as I had melted a hole into it with a previous attempt. (Also why I mounted it down this time)So far, about 2 months in, it's working fine. The brake lights are still as bright as they were before. There hasn't been any issues with them cutting out, and the failure light hasn't come back on.If ever they do get loose, I'll crimp some male and female connectors into the system, so that they can be removed in the future if needed, in case they ever need to be replaced, or a future owner wants to go back to incandescent bulbs.For now though, they're perfectly fine.

I used these to stop a flicker in my truck’s interior lighting. Very easy to install and work well.

No possible way to make this work for my 23 Suburban with the 921 reverse light. Nothing like a factory to be able to lock in place so if you can actually make it work, there will be no way to lock the bulbs into place in the housing.

I specifically ordered a 10ohm resistor , received a 8ohm , I did not return the item cuz I know I can use this for another project , would rate 5 stars if I had gotten my order correctly but overall great build and durability

Quedaron funcionando las luces secuenciales de mi Cadillac

Cumple con su función segun lo descrito por el vendedor

When buying led light for trucks trailer or anything you need to buy these quality products and really cheap , easy to wire up as comes with the electrical connector , and it will stop hyper flashing issues you have now I have bright led lights

This item is very easy to install. Works great. Good price.

Es lo que ofrecen