UtheerGrill Replacement Parts for Weber Spirit and Spirit II 300 Series, 15.3" Flavorizer Bars, 18" Grill Burner and Ignitor Kit for Weber Spirit E310, E320, S310 with Front Control, 7636, 69787

This product looks exactly like the original "Webber" product. I bought the 3 burner (Natural Gas) grill at Home Depot about 6 to 8 years ago. I have contacted Webber to warranty parts in the past but for some reason I bought this replacement kit. I am glad I did- finally I got my ignitor back again. For the last year or 2 the ignitor just didn't lite the burner. I tried new batteries and bending the electrode, I wrapped a copper wire around the burner near the ignitor but nothing worked.I am a HVAC service tech so I am use to working on furnaces so this wasn't too hard to figure out. I decided to make it more challenging by doing it after dark with a flashlight. Remember to Shut Off the gas supply first. The main thing is to take the front control panel off and let it dangle by the internal gas line while you pull the burners out. A lot of Phillip's screws and two- 7/16" bolts hold panel in place. Also take the gas line support loose on the right side. Don't disconnect or severely bend the internal gas line. The washer headed screws at the back of the burners were hopelessly rusted in place. Fortunately the burners slid out under them I pulled out burners through the front.The left burner has a clip that holds the ignitor electrode in place. The mounting bracket on the new burner had to be pried up to get the ignitor to slide in place. Be careful use a flat blade screwdriver and pry just enough to get it to slide. This tight connection is critical and I think why my old one wasn't sparking right. This provides the grounded connection for the ignitor. It has to fit tight metal to metal. Make sure it pushes tightly and completely into place. Rout the wires just like the old ignitor system. The electric control module fits in place just like the old one and the wires are easy to figure out. While the burners were out I cleaned up the burner bowl and used pliers to grab the 3 rusted screws in the back of the burners and slowly unscrewed them. The kit came with 3 new screws. The screws don't hold the burners tight. They do keep the burners in place. The burners are all different so each of the three fit in only one way. Put the crossover tube and burners together carefully - study them to be sure the flame holes all face the right way and that the crossover tube will carry the flame across the the next burner.After it's all back together it lit with the ignitor but the flame jumps around off the burners and the burners didn't stay completely lit. This is the important tip that the instructions don't mention---- each burner has an air shutter at the front end that may need to be adjusted. The shutters also have a metal screen to keep bugs out - don't remove the screens Just loosen or remove the shutter set screw with the burners working and carefully adjust the shutters to make the flame stabilize. This is easier in the dark so you can see the flame. A well defined blue flame is what you want. I found closing the shutters to 1/4 to 1/3 open worked best for my grill. Watch the flame on the cross over tube as well it should be small but a continuous string of flames. Move the control knobs slowly between hi and low and make sure the burners are blue and stable. Don't just go for the biggest flame from the burners. Look for the largest well defined flame on high without a rolling/ dancing type flame. Tighten the set screws back to hold the shutters in place. Propane has a much higher pressure than natural gas so adjusting the burner shutters will be different but same thing applies look for a strong well defined blue flame on high. Orange tops on the flames are not good and should be adjusted out as much as possible using the shutters. Orange flames are inefficient flames and produce more carbon monoxide they are usually more common in dirty or rusty burner tubes.I've cooked several steaks in the 2 weeks since I rebuilt the burner and it seems to work like new.

Great replacement part, fits perfectly, Easy to install

Excellent instruction booklet with clear process and procedure to remove old pieces and replace with high quality new parts. This old Weber grill now lights, heats and cooks like it was brand new!! Highly recommend this kit.

This product fits nicely into my Spirit 300 that is well over 10 years old. I would give 5 stars but I purchased same set less than 3 years ago and it rusted out. But, for the value it is worth not having to purchase a new/same model at $899. Will most likely purchase again in a few years.

Fit perfectly into Weber Spirit 3 Burner. 20 minute install.

This was a perfect fit for my Weber Spirit II grill. My grill is a couple of years old and the right burner stopped working. I took the grate and burner plates off, thinking it was just out of line. Instead I found a hole in the burner pipe and thought my grill was toast. I thought I’d try to find a fix that would get me to next spring. Instead I found this and figured it was worth a shot instead of buying a whole new grill. It took about 90 minutes to take the grill guts out, clean everything, put this new burner pipe in, top with new burner plates, and replace the grate.These were so easy to install and fit perfectly. The hardest part was prying the starter/igniter off of the old burner bar. I snapped the connector, but I was able to secure it to this burner bar with a bit of wire and it works perfectly. I grilled ribeyes last night and it worked just like a brand new grill. Woohoo, I won’t need a new grill for several more years!

Fast delivery just what I needed worked great very easy to put in. Definitely would buy again. Parts looks of good Quality .

These are a great replacement for the Weber S-330 grill, but the 330 has "four" burners, not three. So, you end up having to buy two packs (six total) of these to replace the four original burners. I may buy a third set (three more burner tubes) so that I have a complete replacement set as backup. I really wish they just sold these in a 4-pack. Eh, that's how they get you.Installation for the burners themselves is very simple. Other than attaching the igniters (which slide from back to front), you just plop them in. There's a really good youtube video that shows step-by-step how to do it. I did run into an issue with replacing the burners. Weber, surprisingly, has the screws that hold the burner down situated where they get corroded from heat, debris and grease. You would think they would engineer a design to either protect the screws or a design where the burners attach inside "without" having to be screwed down. Not to mention, they use a proprietary screw that you won't find at your local hardware store. Shame on Weber. I couldn't remove two of them ( heads almost completely corroded) and ended up drilling them out. I didn't feel like creating new threads, but that isn't necessary because I don't move my grill. The burners stay put on their own.The replacement burners themselves seem just as good as the original. I had blue flame straight out of the box, no adjustment necessary. I have zero complains about the quality. If you are replacing the burners you probably need to replace the igniters and the rest of the internal metal components. Flame tamers, burners, and igniters are over $100 total ($200 if replacing the stainless grates), but still cheaper than buying a new grill and your Weber perform like new.