Dundas Jafine PCLT4WZW Dryer Duct Lint Trap

I opted to purchase and install this lint trap because it made the most sense, functionally. Our dryer is vented to the outside. Unfortunately, the dryer duct has been installed above and almost parallel to the heating duct, and they are located in the crawl space adjacent to our basement. Our dryer became inefficient in drying, which led me to surmise the duct work was clogged. The actual ducting is not a straight course to the outside, which made adequate cleaning a hit and miss. My Wife and I decided to drop the duct in order see and clear any clogging. In the crawl space, I found a puddle of water beneath the ducting…which was caused by moisture and lint blockage that was accumulating in the bend of the duct work and dripping condensation from the seam in the ducting. After dropping the heat duct in order to access the dryer duct, we were able to access to entire duct run, which was well over 10 feet. Ridiculous installation by the home builder in placing the dryer duct above the heat duct and angled to the outside. We cleared over 18 years of lint from the duct - guessing it was 95% clogged. We reinstalled and realized we had a potential hazard on our hands. The Duct Lint Trap has proven to be perfect solution. We can trap and prevent large amounts of fibers from being blown into the ducting. Given the angled installation, there is no way the dryer blower will adequately move the damp lint to the outside or even around the bends in the ducting. I am guessing that only microfibers are accumulating in the duct at this point with the Lint Trap in place. The Lint Trap inline installation allows the dryer air to remain vented to the outside and minimizes any concern with air quality in our laundry room and home. The Lint Trap puts my mind at ease in that lint is not accumulating in the duct given the amount of lint trapped and removed after each drying cycle. I personally believe the ducting to the outside can become a fire hazard, even more so when you cannot clean the duct work thoroughly over time. I highly recommend the Lint Trap for anyone that cannot or is not cleaning their dryer vent and duct routinely. I gave the Lint Trap a ‘4-Star’ in the “easy to clean” option because you should use both hands, one to pull the lint filter out and the other hand to catch the falling lint as the “dry” lint will fall away from the filtering screen as you remove the filter and possibly jar or shake the filter. This is not case if the trapped lint is damp during removal. Currently our Lint Trap is installed vertically. We will install it horizontally when we replace our washer and dryer in future. This will allow us to conceal more of the accordion duct behind the dryer and give access to the lint trap which will be partially hidden behind the control panel of the dryer. Great Product and I highly recommend!

This in-line filter is exactly what I was looking for. My dryer is in my garage. When it runs it gets noticeably hotter and more humid. Unfortunately, my dryer is not on an exterior wall so I can’t vent through the wall. The only option I have is a roof vent. However, I don’t want lint all over my roof. This filter is perfect for my application. Hot, humid air out and lint trapped.The filter box is plastic and the filter is a thin wire mesh. It was easy to mount, but be careful not to tighten too much or the screws may crack the plastic. The plastic door latches securely so far. Other reviewers suggest adding something to secure it. It is a perfect fit for 4 inch duct work. Overall very satisfied with this product.

The device does apparently work and is likely strong enough, but a reinforced siding might be useful where the placement is less well protected and may be vulnerable to some damage. It has to be accessible to remove the filter for cleaning, so that it requires exposure and unless it is placed behind a barrier, the washing area could perhaps see some vulnerability to its exposure. The plastic construction should hold up to routine contact, but may be less tolerant of an impact from incidental unplanned contact. Even a reinforcing external metal strip about the box could increase its strength. The fitting rings might also have a raised rim to separate the placement of the incoming and outgoing tubing so as to prevent some resistance to the chamber door remaining closed. I attempted to see if this could be a problem. If the tubing is placed too close to the box, it does interfere with the secure closure of the box so that even an 1/8 inch lip by the box preventing overly close fitting of the tubing would be a very simple modification and prevent problem installation.The filter and its fitting require no address.I have had no problems using this in limited trials and expect that it should continue to work well.

Great addition to our laundry room. Our dryer vents to our patio so we would often find lint all over. We have a samsung dryer and the lint trap does not seem to catch everything, especially at the beginning of each cycle. We replaced the dryer's flexible duct with rigid ducts and installed this at the same time, just above the control panel on the dryer. It is easy to check and easy to clean and it is really satisfying to clean the dryer's trap, then close the door, turn on the dryer and see the rogue lint get caught by this device. Installing it was easy, but the final install is not as clean looking as I would prefer. Having some couplings or duct tape in the box would have been nice since we had to get some to finish the install. Between this device and the new smooth ducts, I feel like our dryer is much safer and at less risk of a lint fire. Since installing it, I have not found any lint on our patio.This unit is also nice because we can open the door in the winter to get some humidity into the house while we dry our laundry