1.5 Inch Stem Casters, DICASAL Double Brakes Black PU Imperial Inch Screw Thread 360° Swivel Caster Wheels for Furture Carts DIY Stands 4 Pack

Excellent well built rollers. Very heavy duty Highly recommend.

These were perfect for my umbrella stand. There so good at locking that my umbrella did not move during the storm. I was worried the poll would snap. I highly recommend these wheels.

I am reusing an old printer stand as a work cart. The stand itself has a good solid frame and top, but the original casters are cheaply made, with hard plastic wheels that hardly move anymore. These new casters are much better; they roll and caster easily, making my 'new' cart quiet and easy to move around. The brake levers are a bit large for the casters, but they 're not in the way and work well. I may buy another set for another cart.

These wheels are just short of perfect. The wheels are excellent: no noise, non-marking, solid. They rotate easily...good bearings. A very sturdy design as there is little offset between the wheel axle and the stem (so less likely that the unit will crush under extreme weight). Here are the only two issues I found. Neither were big enough for me to return, but they may cause me to hesitate to buy again and that's a shame:1) Biggest problem: the stem is poorly designed in terms of how each element is stacked on the screw bolt. In its current design (as of this writing) the wide black metal collar over the wheel has a big depression in the center. This means that the pre-installed nut screwed onto the stem rests into this depression. This leaves very little of the nut exposed beyond the collar. This means that when you screw the stem bolt onto your shelf leg, there is virtually NO space in which to tighten the bolt onto the shelf leg. The included mini wrench is a nice bonus, but even that tool is too thick to get in the space. Moreover, jamming the wrench in there scrapes the bottom surface of the shelf leg! Bad! So I had to hack the installation by adding a second nut to the screw stem and THEN installing the wheel. This, of course, gave me plenty of nut surface to tighten the wheel to the shelf leg, but this hack looks sloppy and now gives TWO opportunities for unintended loosening down the road. SInce I don't plan to load these sheles with too much weight, I think the hack will work, but if this was a heavy load project, I'd return the wheels.2) the locking mechanism is very robust, however, it is SO difficult to engage, I had to put my entire body weight on the mechanism and it was still hit or miss if I could engage it. I weigh 150lbs, so it should engage! Upon inspection, I realized that the mechanism is one of those types that has to literally "bite" inito the wheel to brake it. But given the softness of the wheel (good for silence), the edge of the brake sinks into the wheel surface, thus making the locking tab's movement arc ineffective as a lever to easily bite the wheel. This arc is naturally very limited when the wheel diamter is only 2"...if the tab were longer, it would likely scrape the floor when engaged -super bad. On the wheels where I was finally able to engage the lock, I looked at the brake and the biting edge literally sank into the surface of the wheel, making me worry that, over time, the wheel's surface could become cut and ragged and start to not roll as smoothly. So I think that either this locking mechanism needs to be adjusted to bite the wheel in a different way or an entirely different locking mechanism is needed here.

very good product. I got this for my secret lab Magnus XL since the company don't make one for it. I'm glad I did, the tools included was especially helpful. love the casters

Good quality

Casters are strong enough to easily handle this conversion of bureau-to-kitchen island project. Came with most necessary hardware. Only exception was the large hex key needed to install the inserts for the wooden legs to accept the casters’ screw shaft. Brakes are functional and work fine

I bought these to mount on the bottom of my pinball machine legs, and they worked out perfectly!Even though I did not need all of the included parts, the kit comes with mounting nuts, washers, and even special anchors, for setting these machine-threaded casters into wood. The locking mechanisms are also effective, and easy to lock/unlock, using just your foot.HIGHLY RECOMMENDED!