3M Auto High Strength Red Lens Repair Film, 03341, 3.75 in x 7.75 in

This is easy to apply and really stays on. I had a fix-it ticket for a broken tail light and it was going to cost a ton to replace the light. I applied this, following the directions, which only took a few minutes. The police signed off on the ticket, mentioning they had never seen this before but that it satisfied the requirements for the repair. The film is waterproof and has stayed on perfectly for several years!

I broke my backup light because I was distracted... I removed the loose plastic and cleaned the surface with isopropyl alcohol for good adhesion. Cut a piece of the 3M lens repair tape and then applied it making sure to get all the edges down by rubbing them down well without cracking more plastic; I will replace the lens in the future. Durable? Time, rain, heat, sun, and cold will tell, if I become complacent and don't replace the whole taillight lens. Waterproof, it's plastic tape with good 3M adhesive, and from my experience with 3M, it should work well in the rain. For ease of cutting, I quickly cut with a pair of old scissors. Value for the money, that is a yes. Much cheaper than a ticket.

Turns kinda dark red, hangs on well.

Worked perfectly to patch up a hole in my taillight. Just dissapointed I could not find this product localy.

I repaired a broken brakelight lens with this stuff. Here are my impressions: -- WHAT SIDE IS THE FILM ON: Its difficult to determine what side the removable film is on. They should put labels on it so it's easy to see. -- DONT CUT TO SHAPE OF BREAK!: The instructions state to cut out the film in the shape of the break with a 1/2" overlap. This is a mistake. It's better to leave the film rectangular as it will then better blend with the other lines of the brake light. -- NO CLEANER PROVIDED: The instructions specify a 3M pre-treat on the lens, but nothing is provided in the kit. Not even a tiny little dropper, which is all that is needed. -- TRACE ON WRONG SIDE: The instruction states to trace the broken section on the 3M material. If you happen to trace it on the film size, since it's impossible to tell, you will trace it backward,s and it won't cover the break properly -- COLOR MATCHES: The material color is a good match for the brakelight lens. -- USE ALCOHOL TO CLEAN: Since the kit is not provided with the specified fancy 3M cleaner, I used alcohol to clean the lens before applying the 3M material. That seemed to work fine. -- ADHERES WELL: The 3M film adheres well to the brake light lens. Time will tell if it prevents wanter infiltrating. -- AGRRESSIVE TACK: The adhesive is very aggressive, but with a small area of an edge attached, I was able to pull it off to reposition, and the area that contacted seemed to still adhere when I reapplied it. CONCLUSION: Good Adhesion and Color, No Cleaner Provided, Its a Mistake to Cut to the Shape of Break

This product is freaking AWESOME!! If I could give six stars I would in a heartbeat. A new assembly would have cost me a hundred bucks. This cost $9. It was extremely easy to apply, and you can't even tell there was ever damage to the tail light unless you get about 6 in away from it and know where to look. I applied it 6 months ago and it looks as good as the day I put it on. No leakage at all. Before and after images attached.

Someone “bumped” me in a parking lot and went away. I had no idea for several days when I happened to notice white light leaking through the red stop light on the driver’s side. My 2018 Corvette Stingray had never had so much as a scratch and I was very annoyed! I checked the price for a new stop light lens and they were $400 each! The chip was a small triangle at the bottom right side of the lens, I cut the patch to cover the sides of the break by a half inch and pressed in place. It’s been several weeks now, the chip doesn’t show at all and I have to look closely to spot it myself. I suspect that I’ll eventually bite the bullet and buy the OEM replacement, but the little patch is doing a great job! The kit contains clear, orange, and red lens material more than enough to cover most chips. The lens material is thick enough to be strong, thin enough to sculpt to curves and comes with a strong adhesive painted on the inside of the lens, cut your shape, peal the tape off and stick the patch on. I highly recommend this product!

Terrible product. Doesn't stick

I like this product because the color was very good the light transparency was good and the adhesion was outstanding

great tape works well for my car light

Buen producto, buen reflejo y mejor el pegamento de la cinta

It’s really a great product. Totally worth it. One should have this for fixation of lights.

If you’re as sick of Chinese knock off tape as I am, buy this. 3M know what they’re doing - it’s worth the little extra it costs Successfully repaired a leaking carpet cleaner, and am about to tackle a Dyson vacuum with failed seam welds