White LED Interior Lights Kit for Toyota RAV4 2016 2017 2018 2019 2020 2021 2022 Super Bright 6000K Interior LED Lights Bulbs Package + Install Tool

This kit came with enough bulbs for: • Vanity mirror lights • Front overhead Cabin lights • Rear overhead Cabin lights • Rear right side Cargo light With two bulbs to spare (my license plate lights seem to be permanently affixed LEDs, but your mileage may vary. Installation was fairly easy, with the exception being the front overhead Cabin light. To pop this one off, you want to insert the tool on the rear facing side, and once there is a gap big enough, pull down with your fingers. It takes a fair bit of force, and I ended up breaking part of my front right clip (though it was still functional) Once the console is released, it's smooth sailing with two twist lock bulb holders. You could unlock them with the plastic tool, but I was able to do it myself with just my fingers. Be careful not to burn yourself, if the bulbs were on during or before removal. Once completed, use a flashlight to align the FRONT MOST (windshield side) clips with the holes, THEN align the rear side. If you do rear first, the front will not snap in and you will need to pry the rear off again. Both vanity lights come out by inserting the pry tool on the LEFT side of both assemblies. Then you can tip it down, and slide left to fully remove the assembly with an inch or two of wire to move around. Slide right side back over BEFORE snapping back in. Rear overhead cargo was super easy to get out, but a little challenging to align the bulb during reinstall. There are little cutouts on the clear plastic along the edge, use the pry tool to pop it off. Make sure your LEDs point downward, otherwise you won't gain much light from this! Rear cargo was a little wonky; I opted to unplug the harness (push lever with pry tool and it pops right off super easy) so I wouldn't have to be bent over trying to take it apart. It has a few small pieces so be sure not to lose them. You have to release the tabs on the clear piece from the gray housing, once that's done the little switch will come loose and you'll be able to slide the gray bulb holder out of the gray shield. Replace bulb, put switch back in the groove, and once everything is back together, snap the clear plastic back on. Then just plug it back in and you'll be golden. As I said earlier, my license plate appears to have permanently affixed LEDs as I was unable to find a panel to remove that allowed access. Since it's already led, I didn't see a reason to dig deeper. Your mileage may vary. I opted to keep my bulbs in the same bag as my two extra bulbs, in case I ever need them. I'd recommend holding on to them just in case, small bulbs like this are usually relatively expensive and when you need them, you NEED them. I'll try to update my review down the road and keep you posted on how long these last; they seem to be pretty high quality with good solder joints and personally, I don't see them failing any time soon unless I got faulty LEDs. VERY impressed that they dim when the car dims them, I was expecting flickering from voltage drop, but no such thing happened. All in all, I'd recommended this set to a friend given my experience so far. Very impressed with the quality for the price, I feel like you'd spend more at the auto parts store for worse bulbs. Though, only time will tell.

It’s nice and bright and a cool white! I don’t like warm dim white light as my original lights were that but these are nice bright and fit perfectly.

Some people say to get brighter (more expensive) versions, but I found these bulbs to be plenty bright enough in a pitch black night. The install itself is "simple" but I would not necessarily say it's "easy". The map lights (the ones above the center console) are the worst! Wayyyyyy harder to remove the trim than I thought it would be. I actually ended up half removing the trim and just popping out the lens covers for the bulbs, which slight cracked some of the holding tabs, but I could not otherwise remove the trim for the life of me! The vanity lights are fairly straightforward. Make sure you pop out the left side (driver side) of BOTH vanity light, because the bulb/connector runs to the right (passenger side) and you don't want to dig your trim tool into that. The backseat light was probably the easiest. The cargo light was easy to pop out, but the bulb is hidden under this annoying plastic cover/shield that is tricky to remove. The bulbs themselves are easy to remove, just pull them out (not twist/unscrew), and then the new LEDs just slide in until they're snug. All in -- absolutely worth the upgrade!

I have to start with a word of caution. While the OEM map light bulbs are horrible, they are VERY difficult to replace. I saw some videos that suggested taking down the whole assembly and replacing them from the back. After managing to take down just the clear lens on the drivers side, I struggled so much with the other side that I made a half-hearted attempt to do that, but it seemed even more difficult. I did end up breaking off a small retaining tab on the passenger side housing, but with it back together it seems totally secure. But I think I just got VERY lucky that I didn't break anything critical. As to the product, it's MUCH better than the original dim bulbs. Just doing the lights under the visors, which take the same replacement and are very easy to do, would be worthwhile. That being said, I actually decided to go with a slightly more expensive LED because when I put the Autogine into the map light socket, it didn't seem like a very tight fit. I was concerned that it could vibrate loose, and it seemed like only a little movement would break the connection. And I was not about to risk having to pry off the lens again if I could help it. I won't mention the competitor by name, but their bulbs are brighter and have no polarity, and fit VERY snugly (maybe a little too much). They also aren't sold in convenient sets like these are, but a pack of 6 of their T10 LEDs for $20 allows you to do 2 map lights, 2 visor lights and the cargo light with one to spare. So I'm giving these 4 stars because they're very bright and come in a convenient set. But there's a 5-star option that's not much more.

These bulbs are super bright and easy to install.

Bright and great. Will purchase again. Long lasting.

Instructions weren’t the greatest, but a couple of YouTube searches later and I have them easily installed. Work wonderfully and illuminate the cabin of my 2016 RAV4 beautifully.

La verdad no creía que hubiera mucha diferencia, los coloque y la verdad me lleve una buena sorpresa. Los recomiendo. Ahora tengo que ver qué duren pero llevo una semana y todo bien

Changing the interior lights makes a world of difference. For the overhead lights drop the whole console. Way easier and you are not going to risk damaging the covers. Panel tabs in front corners between roof lining.

Item received was as described, worked perfectly. Great update for the current internal lighting.

Very bright daylight bulbs! Love it! Very quick and easy to install!