Hally Stainless Steel Table for Prep & Work 24 x 30 Inches with Caster Wheels, NSF Commercial Heavy Duty Table with Undershelf and Backsplash for Restaurant, Home and Hotel

Just got a Ooni 24" pizza oven and needed a table for it. After agonizing over getting one and reading reviews of a few tables that fit my requirements. I chose this one. I am quite pleased with it. very manuverable and also stable when you lock the wheels in place

I purchased this for a 200lb ice cream machine and it supports it very well.Don't be like me and miss the fact that the table is 34" tall without the wheels. The wheels put it over 38". Nothing an angle grinder with a cutting wheel can't fix in a few minutes.This comes with 4" diameter solid and durable wheels that are much better than I expected.

Arrived in perfect condition. Easy assembly , looks great .

30" x 48" will fit Ooni Karu 16 pizza oven with door. If placed front to back on the 30" side, the 3 folding legs of the oven are about 2-3 inches from the table edge and the oven door will hang over the edge of the table. Positioned this way gives almost 2 feet of prepare area to the side of the oven. If placed front to back on the 48" side, you are able to have support for the oven door when opened, but lose most of the preparation area. My table arrived with only one small 1/2" scratch on top, and no dents. I'm using a fire pit heat pad between the table and pizza oven, so I'm not concerned with the scratch. Hardware set screws were pre-installed in the table top and shelf and need to be loosened to allow install of the table legs. A 4mm hex wrench and two spare set screws came in a separate bag. Consider a hex drill bit as using the included tiny wrench can wreak havoc on old arthritic fingers. Other reviews commented on the wheel casters being difficult to install and/or easily fall out. You need to have a pair of very grippy gloves ( I used textured latex chemical gloves) to grip the circular plate just above the wheel to keep it from spinning while using a pair of channel locks to tighten as much as possible the small silver plate at the top of the wheel post. Tightening the top plate puts force on the black rubber bands to make them expand outward. If you tighten enough, you should have to force the casters into the legs. If the casters slide in with little or no resistance, then the small plate needs to be tightened more. I will only be rolling this table from my garage to the driveway about 10 feet, so I'm confident the wheels are secure enough for that. I would not recommend trying to push this table through a lawn. I currently have the 66lbs Ooni Karu 16 pizza oven and a Cosori air fryer on top and there is no bowing. I have the lower shelf rested directly on top of the casters (lowest possible setting), to provide maximum support and not have to deal with leveling the shelf in another position. The shelf is locked in using 2 set screws for each leg, which I didn't feel confidently would safely hold the 300+lbs as advertised. Lowest setting allows for placement of the propane tank below and away from the pizza oven with can get up to 950 degrees. Product is made in China. Shelves packaged between two styrofoam sheets in a flat box. My box arrived without any noticeable damage, but if not handled with care, I can see why so many have complained there tables were dented and scratched. I needed a dolly to get the box from my front door to the garage. Recommend two people carry, or remove contents from box at point of delivery and take a couple trips to move parts to the intended install location for assembly.

Wheels were missing but they send me replacements. Tables looks great and easy to install!

I ordered this to use in the kitchen for food prep and a safe surface for an electric skillet and Instant Pot. I got this for a reasonable price ($129.99 for 48 x 24 size with backsplash and casters). I would only give it 3.5 stars for the following reasons: 1) The table is too tall even with the plastic feet. I really wanted to use the casters, but they will make the work surface approximately 38 9/16” from the floor, which is chest high on me, rendering it unusable. 2) I don’t like the plastic feet. They were hard to get in and will be near impossible to remove. Worst of all, the piece that rests on the floor is narrow in diameter and about 1” or so tall. Would be much better to have something that inserts into the hollow of the leg for support but only sticks out 1/4-1/2” and is wider in circumference than the leg. I would not place the plastic feet directly on the floor, as they will likely damage the floor. I have them sitting on very thick, large furniture sliders. Unfortunately, that adds even more height to an already too tall table. 3) The directions were incomplete. There were 4 gray plastic “things” in the box that were nowhere in the list of contents nor the directions. I finally figured out these were “feet” that could be used in lieu of the casters. The directions made no mention of loosening the screws that were already in the holes in order to get the legs through the holes. I did not realize those were screws at first and thought I had a defective table because none of the legs would fit through any of the holes. 4) The casters are HUGE. I have a 72” tall 48 x 18” inch stainless wire rack that has casters and weighs more than the table. These casters look like monster truck wheels next to those casters.PROS: While the table doesn’t look flawless, mine had no noticeable dents or obvious damage. While the plastic was tedious to remove, it wasn’t that hard.TIPS :Attaching the SHELF to the legs: Use a measuring tape to measure from the bottom of the leg to the bottom of the shelf ring. Use an exact number (I used 9 inches even) and measure each leg as you find the right height to tighten the screws. This will make it easier to get the shelf on evenly.If the table WOBBLES after setting it upright, loosen the screws connecting the table top to the legs. Then check the bottom shelf and adjust those screws a little if needed. Retighten all the screws, working opposite ends (back right and left front, then vice versa). Check for wobbles again.I think the table itself is a good option. I am just really disgusted by how excessively tall the table is. I may see if I can find a neighbor who can cut the legs off shorter so I can use the wheels.

Solid table that helps me move around when needed. No real cosmetic issues.I would buy again.

Despite the 1 and 2 star reviews I found this product easy to construct. I removed the film by starting at a corner and rolling the film to the other side. I accomplished this in 15 minutes. I anticipated difficulty putting on the wheels, but I found by using my vise I was able to expand the rubber bladder and easily mounted and tightened all 4 legs in another 15 minutes. We are impressed with the quality of this product and feel confident that the table will safely hold our freezer dryer. I had one minor problem as the promised Allen wrench was missing, but I used my Allen wrench so it wasn't a problem at all.