Jet-Opaque II Iron on Heat Transfer Paper/Dark Color 25 Sheets 8.5x11

Worked well for 20 t-shirts I made for a club get together. After several washings, they're still holding up well. A couple bits of advice: The background of the transfer is white, not clear. So what ever you're printing will have a white background, border, etc. If you don't want that, you'll have to print with the desired background color. Keep in mind, that will use a lot of ink. Also keep in mind that if you don't want a white border around what ever you are printing, you'll have to cut out around the design. Not that big of a deal until you have to do 20 or more in a row. I used cellophane tape to GENTLY remove the backing paper from the transfer before placing on the shirt. Plan on doing one or two practice transfers first, on an old t-shirt. I used a hand iron to press the transfers with the following advice: Press straight down with the iron using a moderately firm pressure. DO NOT wiggle or move the iron once it's on the transfer. If the iron doesn't cover the whole transfer, pick the iron up, move it to the adjacent area and press straight down. Wiggling or moving the iron once it's on the transfer causes the transfer to lift from the fabric.

Made three shirts today. The first two came out perfect except for the lines created by the Teflon sheet I used. For the third I thought I would try the backing that I had peeled from the image to avoid the lines... if only I had read the instructions here FIRST. Didn't realize there was a parchment sheet (or 2?) included. Re-read the instructions from the package and it doesn't mention that. Now I have a shirt with the backing paper ironed to it. :( Hoping that the paper comes off in the wash.All in all, they work, they look good. If I ever need more, I wouldn't hesitate to buy again. Follow the directions **exactly** and you will not be disappointed.

This product has great body and adhesion if done right. I work for a prototyper, and often we need to mock up logo placement on a fabric product. This has been an excellent solution. We've had great results on nylon and cotton. When printed, the colors look lighter than they will be once heat set.Peeling off the backing can be a little tricky, and you have to make sure not to scratch or damage the printed image at all, or white will show where it's damaged. Scissors are better to cut shapes than an X-acto for the same reason. I set the iron to a medium setting, covered with the Teflon sheet (my pack came with 2), and pressed a *little* firmly for about 30 seconds. The end result is smooth, flexible, and sturdy.

I've been using these for months in my business. My customers love the shirts and so do I. If they are failing for anyone its because of a lack of a heat press. Yes the iron works, but just like they state it won't hold up as well. For best results use of a cutter that can read registration marks is recommended, such as the Cameo Silhouette, and a decent heat press.

I wish I had seen somewhere other than in the comments that this paper is a WHITE BACKGROUND!!! I wanted transparent obviously this is not going to work on lettering! BUT the quality is good so if you dont mind the white background and follow instructions it works good!!

Heads up, not as easy store bought iron ons. Expect to waste a few trying to get just the right setting. I made sure to let it dry completely before pulling off the sheets. If you have parchment paper, use a sheet of parchment paper on top and then let it cool. Once cooled, it should peel right off. I also didn't iron for the full 90 seconds each time. Depending on how big your iron on was. My smaller ones took sometimes only 45 seconds with heat. If it was a full page then it was closer to 1 minute and 40 seconds. Once you get the timing down, they work like a charm! I haven't washed them so not sure how long they will last on the shirt, but I was only looking to have these shirts/iron ons for a one day gathering.

I've thought about this one... And then tried it again... Still a hard no. Edges keep lifting and when I reheat to restick the vinyl to the fabric... It melts. And any vinyl that I try to use that night overlap a little, does not stick... And when I reheat to make it restick... The Jet-Opague II melts... Just a hard, solid, no.

I have tried every kind of transfer paper for dark Ts , this is the best . You will find nothing better. Avery is thin, hard to peel fails and will melt right into a fabric. This is thick and transfers like a dream! I have had nothing but joy from it from the first moment! I am so happy! I could go on and on , I LOVE IT!