DOWNLOAD THE APP
Customer Services
Copyright © 2025 Desertcart Holdings Limited
DOWNLOAD THE APP
Specification： Input Voltage：DC 5V~12V Max Power：120W PCB Size：55 x 37 x 1.6 mm（2.16*1.45*0.06in） Package Included: 1 x ZVS heating Power Source module 1 x heating coil Note: 1. When inductive heating, usually work for 5 minutes to power off cooling. Because the current is relatively large during induction heating, the coil heat is also relatively large. When heating, part of the heat generated by the heated object is transmitted to the heating coil. For a long time, the temperature of the heating coil is high. If the heating coil is connected to the terminal, the plastic part of the terminal will be melted. Therefore, when induction heating, it is best to solder the heating coil directly to the PCB 2. Only some types of materials can be effectively induction heated - mostly magnetic materials such as steel. Materials such as brass, copper and aluminum will be very difficult to heat. 3. A large capacitor placed in parallel with the supply voltage can help reduce the voltage/current drop that prevents the unit from starting. 4. This module should not be operating when no load, otherwise it might burn out the circuit. 5. You can check whether the blue LED indicator light up to see if the power is supplied or the module can functionally work. When the indicator is dim, maybe the power supply is insufficient, should use a higher power supply. Just make sure the power supply is within DC 5-12V. Remark: You can solder the heating coil on the board. Review: It was smaller than I thought it would be however it works well. Review: Perfect for dynavap, you'll need to find your sweet spot cause it clicks fast no matter what unless you modify it to induce a smaller area. Will make a small bolt or nail red hot possibly liquid (I haven't pushed it that far) you absolutely need to solder these connections to the sides of the board. It functions in the ports but with a load it will start to melt the plastic casing for the output ports.
| ASIN | B086V6CYM6 |
| Audio Wattage | 120 Watts |
| Batteries Included | No |
| Batteries Required | No |
| Brand | Treedix |
| Compatible Devices | Personal Computer |
| Customer Reviews | 4.0 4.0 out of 5 stars (318) |
| Date First Available | 15 July 2021 |
| Form Factor | ATX12V |
| Item Weight | 120 g |
| Item model number | TRX2-0033 |
| Manufacturer | zvs |
| Model | TRX2-0033 |
| Model Name | TRX2-0033 |
| Package Dimensions | 8.3 x 5.4 x 5.2 cm; 120 g |
| Wattage | 120 Watts |
J**N
It was smaller than I thought it would be however it works well.
C**S
Perfect for dynavap, you'll need to find your sweet spot cause it clicks fast no matter what unless you modify it to induce a smaller area. Will make a small bolt or nail red hot possibly liquid (I haven't pushed it that far) you absolutely need to solder these connections to the sides of the board. It functions in the ports but with a load it will start to melt the plastic casing for the output ports.
R**R
So Amazon sent me another coil and it works this time. It said that a power supply doesn't work but I have a 10 amp power supply running this and it works. Just make sure you buy some good quality solder. Rosin core for electronics. The pipe solder doesn't work. But I give it a 10 out of 10 this time
T**R
12v too much for this. a 1/4 inch nail blew it. 6v it will work well. 3 for lying.
F**E
I finally tried using this (purchased summer of 2023). Tried to power it using 30V 10A bench power supply at 5V/10A. It made a high pitched noise and the PCB smoked slightly near the soldered connections. It didn't heat a small stainless steel tube at all. Seems to be completely defective. -- update -- The device does work, but only when used with a fast rising voltage. Using a bench power supply set to 12V a momentary push button switch drew about 4-5A. A small stainless steel tube (~4 mm diameter) did heat up, but not to red-hot.
Trustpilot
1 week ago
3 days ago