2 in 1 Mobile Phone Tablet Holder Extended Holder Clamp Clip for DJI Phantom 3 Standard Edition Remote Control

Nice construction...works with Flysky FS-i6s transmitter. I recently purchased the i6s thinking it came with a tablet holder because of the YouTube reviews I had watched... Well the one I bought here on Amazon didn't have it... totally my fault for not reviewing the listing contents better. They do sell the complete transmitter setup for like $30 more. So... in the end I did end up saving a few dollars going this route. No instructions provided, but a quick YouTube search I found a similar product that goes over the installation step by step. Thanks for a great product... came fast and I received what I expected.

It takes a lot of looking at the photos online in order to assemble the pieces, but once done, the product holds my Ipad just fine. The thumb screw needs to be tightened with a screwdriver to make it tight enough to hold its position, but then you need the screwdriver again to loosen the screws so it can be folded up and stored. So it's somewhat inconvenient, but the price for this product is low enough to compensate for the inconvenience.

Had a similar item for a 7" FPV monitor which was a little shakey, so I was skeptical. This comes with a little bag of tools and it fit's together very snug. It has a phone and tablet holder and I would say it would fit my Nexus 7 tablet anything over 8" might be a stretch (literally)!I had one of the cheap phantom backpacks and was easily able to cut out a tidy hole 2/3 of the way down. You can see it with the mount off in the bag.Overall really happy with it, very sturdy once together correctly with nice clearance fro controls and the tools are a handy bonus for travel (no having to take from your main tool set).

As others have stated, no assembly instructions included, just a bag of parts. Before ordering, the picture seemed to make enough sense to me, so I figured I could handle putting it together. Mine came missing a screw. I was able to take the mount to Lowes and come up with a suitable replacement because apparently Amazon didn't have any more in stock to give me a replacement mount.Once I got everything put together, I found that the first piece you put on (that connects to the DJI controller's lanyard loop) doesn't really "lock" in. No matter how you set or tighten the screw, it seems to have some play in it. While not a major issue, I do hate seeing the tablet sitting crooked, so I'm constantly straightening it back out.All that said, once I assembled the mount, my Asus Zenpad Z8 tablet was interfering with me being able to use the sticks on my Phanton 3 controller. No matter how I tweaked things, the tops of the sticks were too close to the edge of the tablet and my thumbs would constantly hit the tablet. I had to invert the base piece 180 degrees (so it's pointing up, not down) and then reinstall everything accordingly. This got the mount far enough up that there is now clearance on the sticks. It's a little wonky, and not how it's supposed to be set up, but seems to be working for me.The tablet/phone bracket piece is nice - I like that you can flip it one way or the other depending on if you're using a phone or a tablet. Only complaint so far about that is that the thumb screw doesn't really snug up enough to hold things in place unless you use a screwdriver. A wing screw would probably have done better here. I also don't know how long the extension springs inside the clamp will last - they don't feel particularly strong, but I imagine for occasional use, they'll be okay.While this isn't a perfect solution, it does seem to work okay. Not sure it'll last in the long run, but it's decent, and not too expensive, so 3 stars from me.

I was skeptical when I purchased this but it turns out to be AWESOME! I just came back from using it with my tablet and it works perfectly. It does not come with instructions on how to assemble, but no problem. The assembly instructions are supplied as a picture within the Amazon ad. I love this and will highly recommend to others. Well worth the price and parts are machined very detailed and nice. Two thumbs up!!!

This is the second one of these that I have had. It’s the best solution to holding my phone on my drone, but the problem is the first one broke and now for some reason, the spacing on the second one is not as wide as the spacing on the first one so, my phone will not hold securely in place unless I take the case off

Once you figure out how to put it together, it's perfect. A little confusing at first putting it together - just follow the pics and you'll figure it out. I did have one little nut leftover that fit nothing. Otherwise, well made and does the job for my iPad Air2 mini.

This came in a plastic bag without any assembly instructions, manual nor any kind documentation. I had to come to this item listing to look at its picture illustration. The mount fitting is misaligned or not properly fabricated fit correctly. What a waste of time.