SUNLU Light Weight PLA Filament 1.75mm, 0.8KG, LW-PLA 350m Low-Density, Active Foaming 3D Printer Filament for RC Planes Drone Parts and Cosplay, Suit Most 3D Printers, White

For being pla+, I expected some need for dialing it in some, and a bit of difficulty with bed adhesion. I'm couldn't have been more wrong. It's important to note that I'm using an Ender 3 V2 with a PEI bed, cr touch module, upgraded hardware and using custom firmware (the "Professional" cfw), so I don't run into too much issue with anything hardware or calibration side. However, without any sort of changes to my normal procedure of using PLA, I got amazing results. The filament has the shine that it's reported and pictured as having. The color is vibrant, and the material has a decent amount of flex before hitting the point of snapping. The 10 pack gives me plenty of material to make toys for my 5 year old and his Pre-K classmates, as well as my professional uses in repair, custom parts for my personally built guitars/basses, and requests for articulated fishing lures. I've had no print errors as a result of filament issues, even when pushing the material to the limits of the stock hotend extruder. So I'm able to crank the speed on draft/test prints, without wasting time or material on bad prints. I've definitely found my go to manufacturer for filament, and I feel that they offer an affordable and quality product.

I dont know how SUNLU does it. All of the filament I have bought, this is my consistent go to. Price and performance are top notch. I do repeatedly buy because of its repeatability. Color changes don't mess up flow rates. for my core XY its a .98 or .97. I get on size prints within acceptable expectations. As long as they keep this up I plan on keeping it on my shelf.

Fantastic filament; printed well on all of my machines (Ultimaker UM2+, UM2 clone, Centari Carbon, FT-5, just to name a few). I've also tried this in a few of the colors and they all print very well and kay down very consistent layers with great surface finish.

Overalll godod filament, prints well. Though I did have issue on three seperate rolls with filament entanblement and failure to feed properly. I will buy more. I'm realigning the spool location which should help entanglement issue.

We’re using this filament to produce a simple part for resale in our business and I have to say it has been without issue since the beginning. We’ve gone through about 30+ rolls with zero crosses, and no issues feeding. Using it exclusively in multiple Bambu Labs P1S units with AMS. We keep four identical rolls in each AMS and it just moves to the next roll when the current one runs out. This allows us to print continuously without interruptions to change rolls. One roll ends it switches to the next roll and continues to print while we replace the empty with a fresh one and it’s reloaded and ready. The AMS doesn’t seem to have any issues with the plastic spool either. Thus, all pros so far with not a single con yet, so as long as it continues that way we’ll continue to order. If you’re looking for a high quality PLA+ filament give the Sunlu a try. A++

The colors are bright and clear with somewhat less visible layer lines.. So clear in fact that you'll see a lot of the infill pattern, keep that in mind when deciding to print with them. Even though it's a PLA+ filament I've stopped using them if I'm printing something large that needs a strong sparse infill pattern like gyroid because seeing a lot of the infill pattern detracts from the model itself. I like it for small and medium sized models with lots of sides and curves where the sparse infill % in low. I have found it's a little bit fussy to print with and that they need to be dried really well. I dried them for 8 hours before I did my first print (box with a hinged lid ), it didn't work well with the tight tolerances. I've recently dried a spool for another 11 hours and got a much more accurate print.

I buy black, white, grey, etc. by the truckload, but every once in a while the kids will come to me and ask me to print a bookmark with a fish on it or something, and I don't have the right colors around. Rather than getting a 1kg spool of something I'm going to use 10g of, these mini spools let me get a bigger variety of colors for a given amount of money. You do pay more per kg of course, but overall you're paying a lot less than if you had piles of 99.9% full 1kg spools sitting around.

I'll update my review if the title is fixed as its currently not as claimed. Its prefoamed PLA-LW. Not active. Active foaming is higher temp if you want to verify. This ones only 210 tops. I do not recommend as its not what it claims to be and was a waste of money unfortunately. The other reviews im seeing here are for other things with the multicolor pack which is very different.

Filamenty drukują się dobrze, nie łamią, kolory żywe.

It is okay but I can't use it for prints with a lot of details

Geweldig filament. Zeker voor de prijs.

Super filament pas de souci dimpression fonctionne parfaitement. Au température demende.

No issues, is as advertised