UTGLeapers Inc., 30mm, 2 Pieces, High Profile Picatinny/Weaver

[This is the same review for the Low, Medium and High UTG 30mm Weaver Mount, See-Thru Scope Rings] Okay, this is a scope ring. What do you expect - they mount on the rail, they hold a scope. Actually these receive the 5 star rating for a number of reasons - with ONE drawback. The Drawback: They say 'See-Thru' which is technically true. However you are looking through a slit in the low rise base that is maybe a 1/4" high opening - so if you can adjust your "cheek to stock weld" AND you can see below both the ocular and objective lenses AND you can still see the rifle's sights - then they are 'See-Thru'. This applies to 'Low Rise' - the Medium and High 'See-Thru' mounts have some functionality. These are one of the 'true' Weaver mounts still available [not Picatinny' rail mounts] and the only ones I've found that fit on a Savage [semi-proprietary - not quite Picatinny, Mil-Spec or Weaver] scope base. The fit and finish are excellent - nice matte - seemingly durable finish. I've used these and mid-rise and high rise on a couple of rifles for varmint scopes so I can attest they hold zero consistently. Two things I do not know: 1. If they hold zero once removed and replaced on the mounting rail/base since I don't remove optics except with 'quick-release' fittings for 'tactical' rifles. 2. I do not know how well they hold up and are durable with heavy calibers - the largest caliber I've used these on is 5.56mm. I currently have mounted 4 scopes using UTG 30mm rings and have experienced and have had no complaints for rifles from 22LR, .17 HMR to 5.56 mm and 5.7 x 28. They do the job as well as rings costing 10x as much. Pros: Cost/Price Finish Ease of Use [the flat top on the ring makes it very easy to level a scope - simple mounting screws with provided allen wrench] Seemingly durable Consistency in product quality [4 different sets low, med, high - all with the same build quality] Value for the dollar Cons: Low rise are not really functionally 'See-Thru' Personally, I would and do recommend this product and would suggest [unless you know specifically where your L.O.S. and objective lenses are on the rifle] that you buy the set of three - low, medium and high so you get the best fit for scope, rifle and shooter. For comments on seller - see seller feedback.

I purchased this for a Hatsan 155 torpedo and it works great . It gives me excellent eye relief and also comes with stop pins and even extra hardware. They are high profile mounts which accommodates a 6-24 ×50 scope nicely. I really like this and purchased 3 more for some of my other rifles. EXCELLENT PRODUCT(I found other mounts for cheaper prices but why risk buying junk when you have a proven product) just purchased another for a Hatsan150 sniper.( The last mount I received seemed a little off and had to shim rear mounts in order to get my scope to zero out,but no big deal. ) late entry I purchased 7 total and last 2 needed to be shimed so I think QUALITY CONTROL is needed. Also make sure you secure the bottom mounts before screwing down your set screw. Otherwise your alignment will be thrown off and your scope will have to be dialed to far left or right and if that happens you know the mount is fighting against the set screw.

Impressive construction and quality.

Just put these on the Akela bullpup as it needs high rings to allow you to get a cheek weld and see thru the scope. These work fine...though some might want Extra-High for a bit more leeway. It's best to have the scope as close to the bore as possible to make ranging trajectory easier to compute...and these are about 2.875" over the bore which makes very close shots need some hold-under with a 20yd zero which is then within 1/2" out to about 50 yds which then starts needing hold over compensation. This is with 18.1 grain JSB Heavies @ 900'ish which is full power in the Akela with hammer settings stock. Probably more in there if you'd want it but 33ft/lbs is pretty decent and much more powerful than the Marauder .22 this replaces. Good rings for a good price...good kit.

This is a great, inexpensive off set mount for your air gun or rimfire rifle. I have one on my Hatsan 95 Vortex .25 and it hasn’t budged after hundreds of rounds. It allowed proper eye relief and scope setup. Something to note, I could not get the UTG Bugbuster 3-12x32 to work in this mount. The bottom of the windage and elevation adjustment housing sits flat on the bottom of this mount. This is not ideal, as the mount clamps to the dovetail from one side, and by the nature of that design, it is *slightly* off center causing the crosshairs of the scope to not be level when the gun is level. So as long as the scope you’re mounting with this has room to rotate, allowing you to correctly align your crosshairs, you should be fine.

I used this to mount a UTG Bug Buster scope on my Benjamin Marauder pistol air gun and it fit perfectly. Good quality, no machining marks or blemishes and nice finish. It is light weight and for the price, cant be beat.

mounted it on the dovetail under the rear iron sights of a Mosin Nagant. Has some set screws, so I drilled slightly into dovetail to make slight indentations on the nagant and used a little JB weld to help secure the works in place. Blue loctite on threads and have about 80 rounds through it and hasn't budged at all. Considering this is really intended for an airgun... I'm impressed.

Sehr gut, hält mein Zielfernrohr zuverlässig auf meiner 308. Einfache Montage.

Die Montage ist schwarz eloxiert und nicht wie bei Sutter schwarz angepinselt . Das Material besteht aus super harten Duraluminium ( Flugzeugqualität ) . Ich kann die Montage von UTG nur empfehlen !!! MfG

De momento cumple bien..

ベクターオプティクスのスコープに付属のマウントリングがごみ過ぎたため、実重要を購入。 実用スペックかつ、コスパもよく、よいと思います。 2000円ぐらいが底値なのでその時がお買い得です。 良いと思う理由は 安くても実パ ボルト、ナットが舐めない 普通にハイマウントリングとして問題なく使えていること Ａｍａｚｏｎで手軽に買えること 悪い部分は 価格の安定感のなさ （自分は2200円で買ったので最低値で買えてなかったです笑）