3 Way Speaker Crossover, PUV-W3 200W Passive Crossover for HiFi Home Audio 4 to 8 Ohm Bass Mediant Tweeter Bookshelf Speakers - 2Pack

I use a 40 watt nad receiver form the 90s. I hooked up speakers that handle each around 200 watts all 8 ohm. No issues. Sounds great. No soldering required which was nice. I like good sound but did not spend much on speakers. All my speakers were under $200 altogether. I put in 8 inch woofer 4 inch mid and a 1 inch tweeter. Put all into a yamaha ns 6490. I just changed all the speakers. Hope this helps. Also bought new all copper wire for connection to receiver and inside the speaker box.

Great upgrade for my floor speaker from just a cap to the tweeter.

I bought this item to repair Fisher ST-9418F vintage speakers. The resistors and capacitors were old and not working properly. I found the replacement parts but they didn't make the leads on the resistors long enough to for me to solder them in. I decided to try these crossovers that matched the specs for my speakers. I should have done this from the start. I replaced the crossovers in both speakers in about 30 minutes. I saved myself hours of soldering and removing old capacitors and resistors. I can definitely hear the quality of the sound before and after. Everything is more crisp/clear. I would definitely buy this item again.

Connections are labeled, easy, and also removable! I restored some older speakers which sounded dull. With these, the mid-range and hi-range drivers really open up, and provided amazing clarity.The bass output does seem to have a hard cutoff at around 45Hz, so the I felt it was lacking for my speakers, which have 12" drivers. I decided to straight-wire the woofers, bypassing the crossover (which was how they were originally wired, using the woofer's natural roll-off) and the bass response was better. The mids and highs still run through the crossover, and are still crystal clear, so I'm still very happy with this crossover. If the bass had a lower limit of say 20Hz, these would be perfect.Still, for the price, this is hard to beat!

I’m using a car audio amplifier for some Dayton audio speakers and the crossover on the amplifier wasn’t giving enough of a full sound for me, (setting high and low pass to 90hz as recommended). These sound fantastic and make the speakers blend fantastically. I do not recommend using a subwoofer with the bass output on this crossover use the 90hz lpf instead because it does not block out the middle-low midrange on the bass output. Instead I recommend using a larger PA midbass-midrange style woofer such as a 8 inch like mine or even a 10 in a 4way set up like mine. A 6.5 would work but I’m not sure it would have as much of the lower midbass range as you larger woofers. Also it says 4-8 ohm but I have one crossover on a bridged channel to my mids and tweets to a final impedance of 2 ohms ( 4-8ohm svc speakers, +and- all wired together on each drivers), so you’ll be safe as long as you don’t drastically exceed the 200 watt rms rating. I’m going to make another speaker as shown in my picture and use it in a dj set up it gets loud and very crispy clear. I can’t record and play Bluetooth at the same time otherwise I’d record a video but I highly reccomend them for a similar to mine setup. The subwoofer is a 10 inch infinity kappa car subwoofer in a 1.5 cube 32 hz tuned birch 4 inch circle ground firing-ported box that works great in home audio or car audio applications as well.

I bought these crossovers for a budget DIY speaker build. Let me tell you they sound Awesome in this 3 way build8oh 100w set up!

I used this in a bass guitar amp, hoping to separate the mids from the lows, since the amp itself is uniquely configured, with a single 15" and two 8" speakers. This crossover didn't feed anything at all via the middle channel, so I've removed it. I have tried several similar units, with equally unsatisfactory results. I'm tired of returning them. Also, the bass response produced distortion, so it didn't do that part well either.

Had to replace the hardwired inline transistors from 1972 Marantz vantage speakers and this works perfectly!Completely replace low, mid and high frequency. Capacitors and transistors providing a crisp and clear perfect sound!Well built circuit board with flawless soldering beads etc. I highly recommend if you're in the market for replacements. Crossover for bookshelf or four speakers!