AC InfinityAIRPLATE T8 White, Quiet Cooling Dual-Fan System 6" with Thermostat Control, for Home Theater AV Cabinets

The media could not be loaded. This works great. It’s easy to install. Everything is high-quality, including the supplies they give you with it even the templates are sturdy and not made out of paper, but made out of plastic, which is really thoughtful. The fans run super quiet. The temperature control is incredibly responsive. The configurations for the control panel are so easy to use. This is the best product I purchased in a while.

Replaced an entertainment center and found that the new one had nowhere near the airflow and clearance that the old one had, causing a couple electronics to overheat. I found this set and it has been an amazing find that exceeded expectations. First, the quality of these fans and the controller are fantastic. The build quality is perfect, no cheap fittings or material to be found. Installation is a breeze if you just follow the instructions and the provided template. The fans fit like a glove. Setup is simple, plug in the fans to the controller and a few simple preference settings and you are done.The cabinet stays ventilated and cool, one fan flowing intake at the bottom and one exhaust at the top. Where I was seeing overheating warnings above 100-110 Fahrenheit and beyond, this setup has kept the temperature well below 100F with a PS5 running and audio equipment. Well worth the purchase and peace of mind.

These appear to be high quality, are not too hard to figure out, are reasonably quiet, and look nice when installed. I have mine running for about a week now.The only difficulty I had was cutting clean square holes for mounting. The included templates were very helpful, but I had no clue what the best tools were for the job. That's on me, though, but you might watch a YouTube or something if you are not a carpenter.Noise wise, it is pretty good, but a little loud at max speed, if it needs to run that fast which it likely will not if properly sized for your needs.

It took a while to find the right fan for my project. We removed an old oven and added a microwave into a new closed space. I’m working on new building new drawers underneath now. I may add another air vent later, if needed.Anyway, I was worried it the microwave might overheat so I added this two fan system. There’s also a fan underneath the microwave and it draws air in and then the fan in photo draws air out on the outside. I set it up so that the fan turns on at 90 degrees right now. I very happy because I don’t have to manually turn the fan on when I gets hot. Also because it looks great and is super quiet. It really works awesome.I had looked at fans that were specifically made for putting in walls and there was nothing even close to quality, quiet-ness, options and price point. This is basically every a really I am computer USB fan. I really couldn’t be happier. In fact if this fan ever broke, all I would have to do is buy another usb computer fan and replace it. Computer fans are really easy to find and they work terrific. That said, I have no reason to buy it from another company I’m just making a point that these are just really high-end computer fans. If they can work in a $3000 computer, they can work for a $300 microwave.This company makes a really awesome products.Fyi, I did scratch the white paint on the edge on one of the fans a little when installing it. I was trying to sand some paint on the wall. Had I done it again, I would have uninstalled the fan before sanding or covered it with some painter’s tape. It really was my fault.

Using this cool down my new entertainment center housing my PS4 and Xbox. Without it, the consoles overheated and shut down within five minutes of being on. With these fans and unit installed it never goes over my set temperature. I can't hear the fans running either.Install process was easy but a hassle. I had to drill holes then saw around, but it was convenient that they included a stencil thingy to place against the wood and trace out. I wish I'd done it outside though because man, the dust. But nothing a vacuum and lots of dusting couldn't fix.The "auto" setting is what I use because its super easy to set up. There's the option for variable speeds and a window for temperatures. I'm in too much of a hurry to figure all that out so I'm glad there's just a simple "auto" setting for me to use. I set the temp, when it reaches that, the fans turn off. When it drops below, they shut off. I'll set up the variable speed temp thingy later.Overall, I'm extremely pleased. The unit works perfect, the install was painless, and the quality is good.

Bought this product to install in a AV cabinet to keep it cooler. I’ve read most receivers need to be kept at around 85 degrees for best performance and longevity.After unboxing I was surprised how nice the fans and control module were. This is clearly a well made fan system. Install was relatively straight forward, just use the templates and cut out the proper size hole. It helps to use a drill bit to get the hole started, then a jig saw to do the rest.After installing the fans, then came hooking everything up. I was a bit disappointed here. The USB connectors take up a lot of unnecessary space and the cables are really long, creating a birds nest of cables behind my receiver. Also really wish I had the option to plug the control module directly into a USB outlet on my surge protector versus using an extra outlet.After everything was hooked up, I was pleasantly surprised by the noise level. They are quiet, but can still be hear from about 15 feet away.

I am very impressed with the design and quality of this fan kit. The included installation templates are excellent: sturdy, accurate and easy to use. All of the components are solid and attractive. I am very happy with this purchase.